A wireless signal, such as a Netgear Extender WiFi range extender, works by receiving wireless signals from a router or access point and transferring them to the end user. When an electronic equipment stops functioning as intended, much like other electronic devices, you might need to troubleshoot it.
You might want to reset your Netgear Wifi Extender for a variety of reasons. But connectivity problems are the most typical culprit. You want to reset it to see if the issue goes away because it hasn’t worked.
Typically, this comes last in a simple troubleshooting process. This typically resolves the problems, but before we reset, let’s quickly review some other troubleshooting techniques that might also be effective. This guide will be of assistance to you, but if you require expert support, get in touch with gearhead support, which is the official support service for all Netgear products.
To reset a Netgear Wifi extender follow the steps given below:
- Locate the “Reset” button on the back or bottom of the extender.
- Use a paperclip or similar object to press and hold the “Reset” button for at least 7 seconds.
- Release the button when the extender’s lights begin to blink.
- Wait for the extender to reboot, which may take a few minutes.
- Once the extender has rebooted, you can set it up again using the Netgear genie app or by following the instructions in the user manual.
Note: Resetting the extender will erase all custom settings and restore the device to its factory defaults.
Why is it necessary to reset the Netgear extender?
There are several reasons why you might need to reset a Netgear Wifi Extender:
- Troubleshooting: If you are experiencing connectivity issues or other problems with the extender, resetting it can often help to resolve them.
- Setting changes: If you have made changes to the extender’s settings and are unable to connect or the extender is not working properly, a reset can help you start fresh and reconfigure the device.
- Forgotten password: If you have forgotten the login password for the extender, a reset will restore the default login credentials, allowing you to access the device again.
- Selling or giving away: When you reset the extender, it will erase all custom settings and restore the device to its factory defaults. This is useful when you are selling or giving away the extender, so that the new owner can set it up with their own settings.
- Firmware update: If you are trying to update the firmware on the extender, it is often necessary to perform a reset before and after the update.
Netgear Firmware Update
Firmware is the software your Netgear gadget requires to operate as intended. Range extender won’t operate without firmware. The firmware may occasionally require update to increase both its usefulness and effectiveness. When you use the IP address to log in, you can check the most recent status of your extender firmware. Your extender could need a firmware upgrade if it is an older model. This may not be a problem if you just bought it. If you are having firmware problems, many manufacturers provide technical support. If you believe a firmware problem is keeping you from utilising the device, don’t be afraid to contact the Netgear technical support team.
Reset the Netgear extender using the web browser
Using this method, the Netgear Wifi Extender reset procedure can be carried out. You can finish this task at home without the use of outside support by using one of the most well-liked and straightforward approaches. To achieve the best results, all you need to do is ensure that you carry out each procedure exactly as instructed, without making any mistakes. Follow these steps to reset your Netgear extender:
- Your Netgear WiFi Extender must be turned on in order to begin the procedure.
- The next step is to switch on your laptop or computer and open the web browser.
- Go to the Netgear Wifi Extender’s default web page right now.
- Enter all of your login details when the login window appears, then click Log In.
- After that, from the Netgear Smart Wizard’s initial menu, choose Factory Reset.
- Select yes to confirm your selection.
Factory Reset through the Reset Button
Hard factory reset is the alternative. Only do this if you are unable to perform the soft reset described above because you don’t know your IP address, username, or password. The gadget has a reset button that you will press to do a hard reset. Each router and extension built by any manufacturer has a hard reset button.
It is clearly marked for Netgear Wifi extender. You’ll need a pin or other sharp object to press this button. Release after roughly 10 seconds of pressing. Resetting the device should be done while it is powered on. As the gadget reboots, you’ll see that the lights will turn off and then on again. Your device’s factory settings will have been recovered after this procedure. The setup procedure will then need to be repeated in order to customise it from scratch.
When you want to pair the extender with another router or switch the extender from one network to another, the reset procedure is useful. Both the soft reset and the hard reset will function perfectly fine. Since you only need to push the button and finish the setup process to use the extender once more, a hard reset is simpler. However, keep in mind that you will remove any wireless network settings and data that were on the extender, including the wifi name, passwords, and other complex technical information.